Iphone 12 pro max size in inches length

Q: Is iPhone 12 Pro Max is a 6.5 inch?

Details: iPhone 12 Pro Max has a 6.7-inch1 all-screen Super Retina XDR display. The back is textured matte glass, and theres a flat-edge stainless steel band around the frame. The side button is on the right side of the device. There are three 12 MP cameras on the back: Ultra Wide, Wide, and Telephoto.

Brand Brand name of the company that manufactures the device. Table of Contents Show Is iPhone 12 Pro Max is a 6.5 inch? How big is the iPhone 12 max length? How long is iPhone 12 Pro in CM? What are the dimensions of iPhone 12 Pro Max?	Apple
Model Model name of the device.	iPhone 12 Pro Max
Model alias Аlternative names, under which the model is known.	A2342 A2411 A2410 A2412

Width Information about the width, i.e. the horizontal side of the device when it is used in its standard orientation.	78.09 mm (millimeters) 7.809 cm (centimeters) 0.256 ft (feet) 3.074 in (inches)
Height Information about the height, i.e. the vertical side of the device when it is used in its standard orientation.	160.84 mm (millimeters) 16.084 cm (centimeters) 0.528 ft (feet) 6.332 in (inches)
Thickness Information about the thickness/depth of the device in different measurement units.	7.39 mm (millimeters) 0.739 cm (centimeters) 0.024 ft (feet) 0.291 in (inches)
Weight Information about the weight of the device in different measurement units.	228 g (grams) 0.5 lbs (pounds) 8.04 oz (ounces)
Volume Estimated volume of the device, calculated from the dimensions provided by the manufacturer. Applies for devices in the form of a rectangular parallelepiped.	92.82 cm³ (cubic centimeters) 5.64 in³ (cubic inches)
Colors Information about the colors, in which the device is available in the market.	Silver Graphite Gold Pacific Blue
Body materials Materials used in the fabrication of the device's body.	Glass Stainless steel
Certification Information about the standards, in which the device is certified.	IP68

SIM card type Information about the type and size (form factor) of the SIM card used in the device.	Nano-SIM (4FF - fourth form factor, since 2012, 12.30 x 8.80 x 0.67 mm)
Number of SIM cards Information about the number of SIM cards, supported by the device.	1
	Embedded SIM (eSIM) support

GSM GSM (Global System for Mobile Communications) was developed to replace the analog cellular network (1G), therefore it is referred to as a 2G mobile network. It has been improved with the addition of General Packet Radio Services (GPRS) and later via the Enhanced Data rates for GSM Evolution (EDGE) technology.	GSM 850 MHz (B5) GSM 900 MHz (B8) GSM 1800 MHz (B3) GSM 1900 MHz (B2)
CDMA CDMA (Code-Division Multiple Access) is a channel access method for communications within mobile networks. Compared to other 2G and 2.5G standards like GSM and TDMA, it provides increased data transfer speeds and allows more subscribers to connect simultaneously to the network.	CDMA 800 MHz (BC0) CDMA 1900 MHz (BC1)
CDMA2000 CDMA2000 is a family of 3G standards for mobile networks based on CDMA and providing high-quality voice and broadband data services over wireless networks. Its advantages include stronger signal, fewer drop-offs and breakups, analog capabilities, very high spectral capacity, etc.	1xEV-DO Rev. A
TD-SCDMA TD-SCDMA (Time Division Synchronous Code Division Multiple Access) is a 3G standard for mobile networks. It is developed as an alternative to the W-CDMA standard in China by the Chinese Academy of Telecomunications Technology, Datang Telecom and Siemens AG, and combines TDMA and CDMA.	TD-SCDMA 1900 MHz TD-SCDMA 2000 MHz
UMTS UMTS stands for Universal Mobile Telecommunications System. Based on the GSM standard, it is deemed as a 3G mobile network standard. It has been developed by the 3GPP and its major advantage is the provision of greater bandwidth and spectral efficiency, due to the W-CDMA technology.	UMTS 850 MHz (B5) UMTS 900 MHz (B8) UMTS 1700 MHz (B4) UMTS 1900 MHz (B2) UMTS 2100 MHz (B1)
LTE LTE is deemed to be the fourth generation (4G) of mobile communications technology. It has been developed by the 3GPP based on the GSM/EDGE and UMTS/HSPA technologies in order to increase the speed and capacity of wireless data networks. A further development of the technology is called LTE Advanced.	LTE-FDD 700 MHz (B12) LTE-FDD 700 MHz (B13) LTE-FDD 700 MHz (B14) LTE-FDD 700 MHz (B17) LTE-FDD 700 MHz (B29) LTE-FDD 800 MHz (B20) LTE-FDD 850 MHz (B5) LTE-FDD 850 MHz (B18) LTE-FDD 850 MHz (B19) LTE-FDD 850 MHz (B26) LTE-FDD 900 MHz (B8) LTE-FDD 1700 MHz (B4) LTE-FDD 1800 MHz (B3) LTE-FDD 1900 MHz (B2) LTE-FDD 1900 MHz (B25) LTE-FDD 2100 MHz (B1) LTE-FDD 2600 MHz (B7) LTE-TDD 1900 MHz (B39) LTE-TDD 2000 MHz (B34) LTE-TDD 2300 MHz (B40) LTE-TDD 2500 MHz (B41) LTE-TDD 2600 MHz (B38) LTE-FDD 2300 MHz (B30) LTE-FDD 600 MHz (B71) LTE-TDD 3500 MHz (B42) LTE-TDD 5200 MHz (B46) LTE-TDD 3500 MHz (B48)
5G NR The 5G (fifth generation) mobile networks use the new radio access technology (RAT) developed by 3GPP, dubbed 5G NR and deemed as the global standard for the air interface of 5G networks. 5G NR operates in two frequency ranges - FR1 (sub-6 GHz) and FR2 (above 24 GHz). In the FR1 frequency range, the 5G mobile networks use a number of bands, some of which are traditionally used by previous standards. The FR2 provides shorter range but higher available bandwidth than bands in the FR1.	5G-FDD 600 MHz (n71) 5G-FDD 700 MHz (n12) 5G-FDD 700 MHz (n28) 5G-FDD 800 MHz (n20) 5G-FDD 850 MHz (n5) 5G-FDD 900 MHz (n8) 5G-FDD 1700 MHz (n66) 5G-FDD 1800 MHz (n3) 5G-FDD 1900 MHz (n2) 5G-FDD 1900 MHz (n25) 5G-FDD 2100 MHz (n1) 5G-TDD 2300 MHz (n40) 5G-TDD 2500 MHz (n41) 5G-FDD 2600 MHz (n7) 5G-TDD 2600 MHz (n38) 5G-TDD 3500 MHz (n78) 5G-TDD 3700 MHz (n77) 5G-TDD 4700 MHz (n79) 5G mmWave 39 GHz (n260) 5G mmWave 28 GHz (n261)

Mobile network technologies There are several network technologies that enhance the performance of mobile networks mainly by increased data bandwidth. Information about the communication technologies supported by the device and their respective uplink and downlink bandwidth.	UMTS (384 kbit/s ) EDGE GPRS HSPA+ (HSUPA 5.76 Mbit/s , HSDPA 42.2 Mbit/s ) LTE LTE-A (500 Mbit/s , 1 Gbit/s ) EV-DO Rev. A (1.8 Mbit/s , 3.1 Mbit/s ) TD-SCDMA TD-HSDPA 5G NSA 5G SA
	Gigabit-class LTE with 2x2 MIMO and LAA

Operating system (OS)

Information about the operating system used by the device as well as its version.

iOS 14.1

SoC The SoC integrates different hardware components such as the CPU, GPU, memory, peripherals, interfaces, etc., as well as software for their functioning.	Apple A14 Bionic
Process technology Information about the process technology used in manufacturing the chip. The value in nanometers represents half the distance between elements that make up the CPU.	5 nm (nanometers)
CPU CPU is the Central Processing Unit or the processor of a mobile device. Its main function is to interpret and execute instructions contained in software applications.	2x Firestorm, 4x Icestorm
CPU bits The CPU bits are determined by the bit-size of the processor registers, address buses and data buses. 64-bit CPUs provide better performance than 32-bit ones, which on their part perform better than 16-bit processors.	64 bit
Instruction set The instruction set architecture (ISA) is a set of commands used by the software to manage the CPU's work. Information about the set of instructions the processor can execute.	ARMv8-A
CPU cores A CPU core is the processor unit, which executes software instructions. Presently, besides single-core processors, there are dual-core, quad-core, hexa-core and so on multi-core processors. They increase the performance of the device allowing the execution of multiple instructions in parallel.	6
GPU cores Similar to the CPU, the GPU consists of processing units called cores. They handle the computation of graphics in various applications.	4
RAM capacity RAM (Random-Access Memory) is used by the operating system and all installed applications. Data in the RAM is lost after the device is turned off or restarted.	6 GB (gigabytes)
RAM type Information about the type of RAM used by the device.	LPDDR5
RAM channels Information about the number of RAM channels integrated in the SoC. More channels mean higher data transfer rates.	Double channel
RAM frequency RAM frequency relates directly to the rate of reading/writing from/in the RAM memory.	2750 MHz (megahertz)
	Next‑generation Neural Engine

Storage

Information about the capacity of the built-in storage of the device. Sometimes one and the same model may is offered in variants with different internal storage capacity.

128 GB (gigabytes)
256 GB (gigabytes)
512 GB (gigabytes)

Type/technology One of the main characteristics of the display is its type/technology, on which depends its performance.	OLED
Diagonal size In mobile devices display size is represented by the length of its diagonal measured in inches.	6.7 in (inches) 170.18 mm (millimeters) 17.02 cm (centimeters)
Width Approximate width of the display	2.81 in (inches) 71.4 mm (millimeters) 7.14 cm (centimeters)
Height Approximate height of the display	6.08 in (inches) 154.48 mm (millimeters) 15.45 cm (centimeters)
Aspect ratio The ratio between the long and the short side of the display	2.164:1
Resolution The display resolution shows the number of pixels on the horizontal and vertical side of the screen. The higher the resolution is, the greater the detail of the displayed content.	1284 x 2778 pixels
Pixel density Information about the number of pixels per centimeter (ppcm) or per inch (ppi) of the display. The higher the pixel density, the more detailed and clearer is the information displayed on the screen.	457 ppi (pixels per inch) 179 ppcm (pixels per centimeter)
Color depth The color depth of the display is also known as bit depth. It shows the number of bits used for the color components of one pixel. Information about the maximum number of colors the screen can display.	24 bit 16777216 colors
Display area The estimated percentage of the screen area from the device's front area.	88.1 % (percent)
Other features Information about other functions and features of the display.	Capacitive Multi-touch Scratch resistant
	Display manufacturer - Samsung Super Retina XDR Ceramic Shield Oleophobic (lipophobic) coating True tone display Wide color display (P3) Dolby Vision HDR10 Wide color gamut Haptic Touch 2000000:1 800 cd/m² typical brightness 1200 cd/m² peak brightness

Sensors

Sensors vary in type and purpose. They increase the overall functionality of the device, in which they are integrated.

Proximity
Light
Accelerometer
Compass
Gyroscope
Barometer

Sensor type Information about the sensor type of the camera. Some of the most widely used types of image sensors on mobile devices are CMOS, BSI, ISOCELL, etc.	CMOS (complementary metal-oxide semiconductor)
Pixel size Pixels are usually measured in microns (μm). Larger ones are capable of recording more light, hence, will offer better low light shooting and wider dynamic range compared to the smaller pixels. On the other hand, smaller pixels allow for increasing the resolution while preserving the same sensor size.	1.7 µm (micrometers) 0.001700 mm (millimeters)
Aperture The aperture (f-stop number) indicates the size of the lens diaphragm opening, which controls the amount of light reaching the image sensor. The lower the f-stop number, the larger the diaphragm opening is, hence, the more light reaches the sensor. Usually, the f-stop number specified is the one that corresponds to the maximum possible diaphragm opening.	f/1.6
Focal length and 35 mm equivalent Focal length is the distance in millimeters from the focal point of the image sensor to the optical center of the lens. The 35 mm equivalent indicates the focal length at which a full-frame camera will achieve an angle of view that's the same as the one of the camera of the mobile device. It is measured by multiplying the native focal length of the camera by the crop factor of the sensor. The crop factor itself can be determined as the ratio between the diagonal distances of the image sensor in the 35 mm camera and a given sensor.	26 mm (millimeters) *(35 mm / full frame)
Number of lenses Information about the number of lenses used by the optical system of the camera.	7
Flash type The rear cameras of mobile devices use mainly a LED flash. It may arrive in a single, dual- or multi-light setup and in different arrangements.	LED
Image resolution One of the main characteristics of the cameras is their image resolution. It states the number of pixels on the horizontal and vertical dimensions of the image, which can also be shown in megapixels that indicate the approximate number of pixels in millions.	4032 x 3024 pixels 12.19 MP (megapixels)
Video resolution Information about the maximum resolution at which the rear camera can shoot videos.	3840 x 2160 pixels 8.29 MP (megapixels)
Video FPS Information about the maximum number of frames per second (fps) supported by the rear camera while recording video at the maximum resolution. Some of the main standard frame rates for recording and playing video are 24 fps, 25 fps, 30 fps, 60 fps.	60 fps (frames per second)
Features Information about additional software and hardware features of the rear camera which improve its overall performance.	Autofocus Continuous autofocus Continuous shooting Digital zoom Optical zoom Optical image stabilization Geotagging Panorama HDR Touch focus Face detection White balance settings ISO settings Exposure compensation Self-timer Scene mode Macro mode Phase detection autofocus (PDAF) RAW Night Mode Dolby Vision HDR video recording
	Sapphire crystal lens cover Sensor-shift OIS 1080p @ 240 fps Secondary rear camera - 12 MP (ultra-wide-angle) Sensor size - 1/3.6" (#2) Aperture size - f/2.4 (#2) Angle of view - 120° (#2) 5-element lens (#2) Focal length (35 mm equivalent) - 13 mm (#2) Third rear camera - 12 MP (telephoto) OIS (#3) PDAF (#3) Sensor size - 1/3.4" (#3) Pixel size - 1.0 μm (#3) Aperture size - f/2.2 (#3) 6-element lens (#3) Focal length (35 mm equivalent) - 65 mm (#3) 2.5x optical zoom (#3) 5x optical zoom range (#3) 10x digital zoom (#2) LiDAR scanner (ToF 3D depth)

Sensor type Information about the sensor type of the camera. Some of the most widely used types of image sensors on mobile devices are CMOS, BSI, ISOCELL, etc.	CMOS BSI (backside illumination)
Sensor format The optical format of an image sensor is an indication of its shape and size. It is usually expressed in inches.	1/3.6"
Aperture The aperture (f-stop number) indicates the size of the lens diaphragm opening, which controls the amount of light reaching the image sensor. The lower the f-stop number, the larger the diaphragm opening is, hence, the more light reaches the sensor. Usually, the f-stop number specified is the one that corresponds to the maximum possible diaphragm opening.	f/2.2
Focal length and 35 mm equivalent Focal length is the distance in millimeters from the focal point of the image sensor to the optical center of the lens. The 35 mm equivalent indicates the focal length at which a full-frame camera will achieve an angle of view that's the same as the one of the camera of the mobile device. It is measured by multiplying the native focal length of the camera by the crop factor of the sensor. The crop factor itself can be determined as the ratio between the diagonal distances of the image sensor in the 35 mm camera and a given sensor.	23 mm (millimeters) *(35 mm / full frame)
Image resolution Information about the number of pixels on the horizontal and vertical dimensions of the photos taken by the front camera, indicated in megapixels as well.	4032 x 3024 pixels 12.19 MP (megapixels)
Video resolution Information about the maximum resolution of the videos shot by the front camera.	3840 x 2160 pixels 8.29 MP (megapixels)
Video FPS Digital cameras are able to shoot videos at different frames per second (fps). Some of the main standard frame rates for recording and playing video are 24 fps, 25 fps, 30 fps, 60 fps. Information about the maximum possible fps for shooting videos at the maximum possible resolution.	60 fps (frames per second)
Features Information about additional software and hardware features of the front camera which improve its overall performance.	Face unlock Night Mode Deep Fusion HDR Face detection Digital image stabilization
	1080p @ 120 fps Cinematic video stabilization

Speaker

The loudspeaker is a device, which reproduces various sounds such as ring tones, alarms, music, voice calls, etc. Information about the type of speakers the device uses.

Loudspeaker
Earpiece
Stereo speakers

Stereo sound recording
Active noise cancellation with a dedicated microphone
Dolby Atmos
Spatial audio playback

Radio

Information whether the device has an FM radio receiver or not.

Tracking/Positioning

The tracking/positioning service is provided by various satellite navigation systems, which track the autonomous geo-spatial positioning of the device that supports them. The most common satellite navigation systems are the GPS and the GLONASS. There are also non-satellite technologies for locating mobile devices such as the Enhanced Observed Time Difference, Enhanced 911, GSM Cell ID.

GPS
A-GPS
GLONASS
Galileo
QZSS

Wi-Fi Wi-Fi communication between devices is realized via the IEEE 802.11 standards. Some devices have the possibility to serve as Wi-Fi Hotspots by providing internet access for other nearby devices. Wi-Fi Direct (Wi-Fi P2P) is another useful standard that allows devices to communicate with each other without the need for wireless access point (WAP).	802.11a (IEEE 802.11a-1999) 802.11b (IEEE 802.11b-1999) 802.11g (IEEE 802.11g-2003) 802.11n (IEEE 802.11n-2009) 802.11n 5GHz 802.11ac (IEEE 802.11ac) Dual band Wi-Fi Hotspot 802.11ax
	2x2 MiMO

Version The technology has several versions, which improve the connection speed, range, connectivity and discoverability of the devices. Information about the Bluetooth version of the device.	5.0
Features Bluetooth uses various profiles and protocols related to faster exchange of data, energy saving, better device discoverability, etc. Some of those supported by the device are listed here.	A2DP (Advanced Audio Distribution Profile) LE (Low Energy)

Version There are several versions of the Universal Serial Bus (USB) standard: USB 1.0 (1996), the USB 2.0 (2000), the USB 3.0 (2008), etc. With each following version the rate of data transfer is increased.	2.0
Features Тhe USB interface in mobile devices may be used for different purposes such as battery charging, using the device as a mass storage, host, etc.	Charging Mass storage Proprietary

Headphone jack

Information whether the device is equipped with a 3.5 mm audio jack.

Connectivity

Information about some of the most widely used connectivity technologies supported by the device.

Computer sync
OTA sync
Tethering
NFC
UMA
VoLTE

Browser

Information about some of the features and standards supported by the browser of the device.

HTML
HTML5
CSS 3

Audio file formats/codecs

List of some of the most common audio file formats and codecs supported standardly by the device.

FLAC (Free Lossless Audio Codec, .flac)
MP3 (MPEG-2 Audio Layer II, .mp3)
AC‑LC
HE‑AAC
HE‑AAC v2
Protected AAC
Linear PCM
Apple Lossless
Dolby Digital (AC‑3)
Dolby Digital Plus (E‑AC‑3)
Dolby Atmos
Audible
Audible Enhanced Audio
AAX
AAX+

Video file formats/codecs

List of some of the most common video file formats and codecs supported standardly by the device.

H.264 / MPEG-4 Part 10 / AVC video
HEVC
MPEG‑4 Part 2
Motion JPEG

Capacity The capacity of a battery shows the maximum charge, which it can store, measured in mili-Ampere hours.	3687 mAh (milliampere-hours)
Type The battery type is determined by its structure and more specifically, by the chemicals used in it. There are different battery types and some of the most commonly used in mobile devices are the lithium-ion (Li-Ion) and the lithium-ion polymer battery (Li-Polymer).	Li-Ion
Charger output power Information about the electric current (amperes) and voltage (volts) the charger outputs. The higher power output allows faster charging.	9 V (volts) / 2 A (amps)
Features Information about some additional features of the device's battery.	Wireless charging Fast charging Non-removable
	MagSafe wireless charging - 15W Qi wireless charging - 7.5W USB Power Delivery 3.0

Is iPhone 12 Pro Max is a 6.5 inch?

Details: iPhone 12 Pro Max has a 6.7-inch¹ all-screen Super Retina XDR display. The back is textured matte glass, and there's a flat-edge stainless steel band around the frame. The side button is on the right side of the device. There are three 12 MP cameras on the back: Ultra Wide, Wide, and Telephoto.

How big is the iPhone 12 max length?

The Apple iPhone 12 Pro Max (14th Gen) has height of 6.33” (160.8 mm), width of 3.07” (78.1 mm), depth of . 29” (7.4 mm), and weighs 8.03 oz (228 g). The Super Retina XDR screen size is 6.7” (170.2 mm) diagonal with a resolution of 2778 x 1284 px at 458 ppi.