How to reset durango after oil change

This message type is displayed indefinitely or

until the condition that activated the

message is cleared. Examples of this

message type are "Turn Signal On" (if a turn

signal is left on) and "Lights On" (if driver

leaves the vehicle with the lights on).

Unstored Messages Until RUN

These messages deal primarily with the

Remote Start feature. This message type is

displayed until the ignition is in the RUN state.

Examples of this message type are "Remote

Start Canceled - Door Ajar" and "Press Brake

Pedal and Push Button to Start."

Five Second Unstored Messages

When the appropriate conditions occur, this

type of message takes control of the main

display area for five seconds and then returns

to the previous screen. An example of this

message type is "Automatic High Beams On."

Your vehicle is equipped with an engine oil

change indicator system. The "Oil Change

Required" message will display in the

instrument cluster display for five seconds after

a single chime has sounded, to indicate the next

scheduled oil change interval. The engine oil

change indicator system is duty cycle based,

which means the engine oil change interval may

fluctuate, dependent upon your personal

Unless reset, this message will continue to

display each time the ignition is placed in the

ON/RUN position. To turn off the message

temporarily, push and release the OK or arrow

buttons. To reset the oil change indicator

system (after performing the scheduled

maintenance), refer to the following procedure.

Vehicles Equipped With Keyless Enter-N-Go —

Use the steering wheel instrument cluster

display controls for the following procedure(s):

1. Without pressing the brake pedal, push the

ENGINE START/STOP button and place the

ignition in the ON/RUN position (do not

2. Push and release the down arrow button to

scroll downward through the main menu to

GETTING TO KNOW YOUR INSTRUMENT PANEL

3. Push and release the right arrow button to

access the "Oil Life" screen.

4. Push and hold the OK button to reset oil life.

If conditions are met, the gauge and

numeric display will update to show 100%.

If conditions are not met a pop-up message

of "To reset oil life engine must be off with

ignition in run" will be displayed (for five

seconds), and the user will remain at the Oil

5. Push and release the up or down arrow

button to exit the submenu screen.

If the indicator message illuminates when you

start the vehicle, the oil change indicator

system did not reset. If necessary, repeat this

Secondary Method Of Resetting Engine Oil Life

1. Without pressing the brake pedal, push the

ENGINE START/STOP button and place the

ignition to the ON/RUN position (do not

2. Fully press the accelerator pedal, slowly,

three times within 10 seconds.

This message type is displayed indefinitely or

until the condition that activated the message

is cleared. Examples of this message type are

"Turn Signal On" (if a turn signal is left on) and

"Lights On" (if driver leaves the vehicle with the

Unstored Messages Until RUN

These messages deal primarily with the

Remote Start feature. This message type is

displayed until the ignition is in the RUN state.

Examples of this message type are "Remote

Start Canceled - Door Ajar" and "Press Brake

Pedal and Push Button to Start."

Five Second Unstored Messages

When the appropriate conditions occur, this

type of message takes control of the main

display area for five seconds and then returns

to the previous screen. An example of this

message type is "Automatic High Beams On."

Your vehicle is equipped with an engine oil

change indicator system. The "Oil Change

Required" message will display in the instrument

cluster display for five seconds after a single

chime has sounded, to indicate the next

scheduled oil change interval. The engine oil

change indicator system is duty cycle based,

which means the engine oil change interval may

fluctuate, dependent upon your personal driving

Unless reset, this message will continue to

display each time the ignition is placed in the

ON/RUN position. To turn off the message

temporarily, push and release the OK or arrow

buttons. To reset the oil change indicator system

(after performing the scheduled maintenance),

refer to the following procedure.

GETTING TO KNOW YOUR INSTRUMENT PANEL

Vehicles Equipped With Keyless Enter 'n Go —

Use the steering wheel instrument cluster

display controls for the following procedure(s):

1. Without pressing the brake pedal, push the

ENGINE START/STOP button and place the

ignition in the ON/RUN position (do not

2. Push and release the down

to scroll downward through the main menu

3. Push and release the right

to access the "Oil Life" screen.

4. Push and hold the OK button to reset oil life.

If conditions are met, the gauge and numeric

display will update to show 100%. If conditions

are not met a pop-up message of "To reset oil

life engine must be off with ignition in run" will

be displayed (for five seconds), and the user will

remain at the Oil Life screen.

5. Push and release the up

arrow button to exit the submenu screen.

How do I reset my dashboard after oil change?