What’s the Benefit?
The electric parking brake provides a higher level of ease and sophistication when operating the parking brake, while the automatic brake-hold feature helps ease the stress of driving in stop-and-go traffic.
The Feature:
The CR-V features an electric parking brake with automatic brake hold.
- Instead of the traditional hand lever or foot pedal for the parking brake, CR-V owners can simply lift the electric parking brake switch to set the vehicle’s parking brake, and push the switch down to release the parking brake.
- When activated, the automatic brake hold maintains braking pressure when the driver applies the brakes, such as in stop-and-go traffic, and releases the brakes when the driver applies the accelerator.
IMPORTANT NOTES:
The CR-V’s electric parking brake can be set to engage automatically every time the ignition is turned off. Here’s how it’s done:
- With the ignition ON and the shift lever in PARK, make sure the brake pedal is not depressed.
- Pull up and release the parking-brake switch to engage the parking brake.
- Pull up and hold the parking-brake switch until you hear a beeping sound, then release the switch.
- Within 3 seconds, pull up and hold the switch again; when you hear two beeps, release the switch.
- The parking brake is now set to engage automatically whenever the ignition is shut off.
- To permanently deactivate the feature, repeat the above process; you’ll hear a single beep at the end to signify that the feature has been disabled.
When using a conveyor-type car wash, you will have to temporarily deactivate the automatic parking-brake function. To do this:
- Bring the vehicle to a stop with the brake pedal and shift to NEUTRAL.
- Turn off the ignition, and push the parking-brake switch down within 2 seconds.
- The automatic activation will be suspended, and will be restored when the vehicle is restarted.
Watch How-To Video
1. Bring the vehicle to a stop with the brake pedal and shift to NEUTRAL. 2. Turn off the ignition, and push the parking-brake switch down within 2 seconds. 3. The automatic activation will be suspended, and will be restored when the vehicle is restarted. Contents
What does it mean when my Honda says electric parking brake problem?
The problem, addressed in a 2016 recall, is that the electronic parking brakes in some models of Honda Civics may fail, allowing the car to roll away when it is in park. … The primary issue in the electric parking brake problem was traced to software in the vehicle stability assist control unit.16 nov. 2018
What does electric brake problem mean Honda Civic?
According to the lawsuit, electric parking brake problems occur because the parking brakes don’t automatically activate when drivers exit the cars or when the driver-side doors are opened. Plaintiff Patrick Rojas says he purchased a 2016 Honda Civic in June 2016 for about $23,500 from a Honda dealership in Florida.9 mai 2019
Owners will witness an “Electric Brake Problem” message on the center screen accompanied by “brake” and “brake system” warning lights illuminated. Often depressing the EPB button and then turning the car off and on will switch off the warnings and engage the drive or reversing gears again.
How do you disengage the parking brake?
Pedal – The pedal emergency brake is a small pedal that is positioned on the floor and to the left of the gas, brake and clutch pedals. Press down on the pedal until you hear it click to engage it. Pull the lever above the foot pedal to release the brake.
How do you release the electronic parking brake on a Honda Civic with a dead battery?
You cannot apply or release the parking brake if the battery goes dead. If you pull up and hold the electric parking brake switch while driving, the brakes on all four wheels are applied by the VSA system until the vehicle come to a stop. The electric parking brake then applies, and the switch should be released.
How do you use Honda electric parking brake?
How do you fix a stuck E brake?
1. Turn your car on. As the engine warms the ice may melt, enabling you to disengage the parking brake.
2. Gently rev the engine. This can help the engine heat up faster, which in turn can speed up the melting process.
3. Try to disengage the parking brake several times after the car has warmed up a bit.
What causes anti lock brake problems?
The most common ABS problems occur when sensors become contaminated with debris or metal shavings. Malfunctions also occur when sensor wiring becomes damaged, resulting in intermittent or no continuity. … If you have a malfunction in the ABS, physically check all wiring and the brake sensors first.
Why is my Honda Civic not starting?
While there are a variety of reasons your Honda Civic won’t start, the most common 3 are a dead battery, an alternator problem, or failed starter.
How do you fix brake system?
1. With the vehicle at rest, apply steady pressure to the brake pedal. Does it feel spongy?
2. Release the parking brake and drive around the block, stopping every now and then.
3. If you feel that your brakes are low, pump the brake pedal a couple of times as you drive around.
How do I reset my Honda Civic?
What is a parking brake module?
The Electronic Parking Brake Module (EPBM) is a module on the CAN bus of most vehicles equipped with EPB systems. Any missing data for vehicle speed, gear position or brake pedal input will cause a problem with the system.
How do you manually release an electric parking brake?
How does the electric parking brake work?
Electronic handbrakes – sometimes called electronic parking brakes – work on the same basis but use electric motors to achieve the effect. Press or pull the button and motors on the rear brakes press the pads onto the discs. You can often hear a reassuring whirring noise as the motors do their work.15 mai 2020