2000 jeep cherokee tail light bulb

Q: Can you replace the bulb in a tail light?

Fortunately, tail light bulb replacement isnt difficult and shouldnt take you more than 45 minutes to an hour to complete. Be aware that newer models may be a little more complicated than older ones, as there will be more wires to disconnect.

Question

Auto & Tires
Automotive Replacement Parts
Car Lighting and Lamps
Car Light Bulbs

Table of Contents Show

How do you want your item?
AmeriLite 1999-2004 Replacement Brake Tail Lights For Jeep Grand Cherokee - Passenger and Driver Side
2000 Jeep Cherokee Front Exterior LED Lights Bulbs Replacement
2000 Jeep Cherokee Rear Exterior LED Lights Bulbs Replacement
2000 Jeep Cherokee Interior LED Lights Bulbs Replacement Upgrade
Can you replace the bulb in a tail light?

Check if this fits your vehicle

Go-Parts

Now $17.95

was $19.95

Now $17.95

was $19.95

Item not available with current selections

How do you want your item?

Notice unusual marketplace activity?

Report

AmeriLite 1999-2004 Replacement Brake Tail Lights For Jeep Grand Cherokee - Passenger and Driver Side

4.5 out of 5 stars213

$80.26

Get it as soon as Wed, Oct 5

FREE Shipping

Only 8 left in stock - order soon.

LED lights bulbs replacement for 2000 Jeep Cherokee headlights, fog lights, tail lights, turn signal lights, interior lights, brake lights, stop lights, dome lights, engine compartment lights, instrument lights, license plate lights, side marker lights, exterior and interior lights bulbs upgrade stock dim halogen headlamps, incandescent or damaged lamps, which will make you drive Better! Safer! Brighter! and Smarter.

It is recommended to double check the stock bulb sizes based on your owner manual or stock lamps before purchasing, as a vehicle's specific bulb type maybe come with different bulbs for different Jeep Cherokee's trims.

2000 Jeep Cherokee Front Exterior LED Lights Bulbs Replacement

2000 Jeep Cherokee Rear Exterior LED Lights Bulbs Replacement

2000 Jeep Cherokee Interior LED Lights Bulbs Replacement Upgrade

Open the trunk door. In order to remove the rear light assembly, it must be accessed with the trunk open.

Remove the three screws that are holding the rear light assembly to the body of the Jeep. Use the wrench to remove the screws.
Each screw is an indented hexagon washer head and is 3/16" in diameter and 3/4" long.
All three screws are identical and can be removed in any order.

Gently pull the rear light assembly away from the car to gain access to the bulbs and wires.
Be careful when pulling away the rear light assembly. The wires will still be attached to the inside of the car.

Locate the brake light. Turn the light assembly over and you will see three light bulb sockets. The brake light is the top bulb and the bulb behind the red plastic lens.

Remove the brake light. Twist the light bulb socket clockwise and remove the light bulb socket from the rear light assembly.

Remove the bulb by pinching on either side of the bulb and gently pulling the bulb out.
Be careful not to force the bulb when pulling as it may damage the bulb socket.

Replace with the new bulb. Gently put in the new bulb in the same manner as you removed the old bulb.

Lock the bulb back in place. Carefully put the bulb back into the light assembly and twist counter clockwise until it locks in place.

Set the light assembly back in place. There is a tab on the bottom of the light assembly that must line up with the hole in the car.
The red brake light should be on top.

Tighten the three screws back into place. This will fasten the light assembly back onto the car.
The order and the positioning of the screws will have no effect on the assembly, because they are all identical.

Check the brake light. Have another person step on the brake to ensure proper lighting occurs.

Can you replace the bulb in a tail light?

Fortunately, tail light bulb replacement isn't difficult and shouldn't take you more than 45 minutes to an hour to complete. Be aware that newer models may be a little more complicated than older ones, as there will be more wires to disconnect.

jeep cherokee tail light bulb